Most people shopping for a concrete contractor get three bids, pick the one in the middle, and find out six months later why the lowest bidder was cheap. The work looks the same for the first week. The difference shows up in year two, when one driveway is flat and another has a crack running corner to corner through what should have been a control joint.
Start with what's under the slab, not what's on top of it
Hanford sits on heavy clay soil, the kind that swells when it's wet and shrinks hard when it dries out over a long Central Valley summer. That movement is the number one reason concrete cracks or heaves here, more than the mix design, more than the finish work. A contractor who knows this ground will talk about base prep before they talk about color or stamp patterns. Ask how many inches of compacted aggregate base they're putting down. Four to six inches over properly compacted subgrade is normal for a patio or walkway. If the soil underneath is soft or has been disturbed, some contractors will over-excavate and recompact before they ever bring in base rock. If a bidder doesn't mention base at all, that's worth noticing.
Ask whether they're using rebar or wire mesh, and ask why. Mesh has a bad habit of sinking to the bottom of the pour if it isn't pulled up and chaired during placement, which means it ends up doing nothing. Rebar set on chairs at 18 inches on center holds its position through the pour. For a driveway that's going to carry a truck, that detail matters more than almost anything else in the job.
Ask about the pour itself, not just the finished price
A driveway slab here usually runs 4 to 5 inches thick, more if it's going to see heavy vehicles or an RV. A walkway or patio can run thinner. Ask what thickness they're quoting and get it in writing, because "standard" means different things to different crews.
Also ask about control joints. Concrete is going to crack somewhere, every slab does, and the joints are there to tell it where. They should be cut 8 to 10 feet apart, and cut within 24 to 48 hours of the pour, before the slab makes its own decision about where to split. A crew that waits a week to cut joints, or skips them on a long run of sidewalk, is setting you up for a crack that runs wherever it wants.
Timing matters more in Hanford than people expect. July and August regularly hit over 100 degrees, and concrete poured in that heat can flash set on the surface before it's properly finished underneath, which weakens the top layer. A contractor who's done this a while will pour early in the morning during summer, keep the slab misted or covered with curing compound, and adjust the mix with a retarder if needed. In December and January you're dealing with tule fog and the rainy season instead, which delays pours for a different reason. Either way, ask how they plan around the weather instead of just scheduling and hoping.
License, insurance, and what to actually ask for
In California, any concrete job over $500 in labor and materials legally requires a licensed contractor. Ask for the license number and look it up yourself on the CSLB website rather than taking their word for it. Check that it's active, check the classification matches concrete work, and check for complaints. Ask for proof of general liability insurance and workers' comp. If a crew shows up without workers' comp and someone gets hurt pouring your driveway, that liability can land on you as the property owner.
Get a written bid that spells out thickness, base depth, reinforcement, joint spacing, and cure time before vehicles can drive on it. Most mixes need about 7 days before you put a car on them, even though the slab will feel hard after a day or two. Full strength takes closer to 28 days. A contractor who tells you it's fine to park on it the next day is either using a different mix than they're telling you, or doesn't care if it's fine.
Permits, setbacks, and older streets versus new ones
If the work touches the sidewalk, curb, or driveway approach into the street, that's usually an encroachment permit through the City of Hanford, separate from a building permit. Retaining walls over a certain height typically need plan review before anyone breaks ground. If you're outside city limits, Kings County handles it instead. A legitimate contractor pulls these themselves and knows the difference, rather than telling you permits are optional or that it's faster to skip them.
It matters where in town you live, too. Homes near the older part of Hanford, around Irwin Street and the Civic Center area, often sit on original sidewalks and driveway slabs poured decades ago with no rebar at all, plus mature tree roots that have lifted panels unevenly. Replacing a section there is a different job than pouring fresh concrete on a newer lot out toward the west side or near Lemoore, where the pad under the house is better compacted but the builder's original base course under the driveway can be thinner than you'd want. Ask a contractor whether they've worked on your type of street before, not just whether they've worked in Hanford.
What makes you walk away
- A bid with no mention of base rock, slab thickness, or joint spacing. If it's not written down, it's not a commitment.
- A price far below the other two bids with no explanation. Thinner slab, no rebar, and less base rock are the usual ways a contractor gets there.
- Pressure to pay a large deposit upfront, more than about a third of the job cost, before any work starts.
- No written contract at all, just a handshake and a start date.
- A contractor who can't tell you how they'll handle a hot pour in August or a wet week in January.
None of this is complicated once you know what to ask. It just takes someone willing to answer straight instead of talking around it. We do driveways, patios, slabs, walkways, steps, repair work, and retaining walls across Hanford and the towns around it, and we'll walk you through the base, the mix, and the joint layout before you sign anything. You can see more about our concrete contractor work and what a job actually involves from start to finish.
